Seepex BN 100-6LS Operating And Assembly Instruction Manual Download Page 38

Page: 38 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

10 (18)

Dismantling/reassembly

9.1.3.3 Pressure branch (700) - Dismantling

Segment retainer (671) - dismantling - pressure branch

9.1.3.4 Suction casing (500) - Dismantling



Remove upper half of the stator (601.o).

–

Conveying product can escape.



Dismantle adjusting segments (635.u).

–

Secure adjusting segments (635.u) to
prevent them from falling down.



Remove lower half of the stator (601.u)
smoothly.

–

Conveying product can escape.



Prop up the rotor (600) with lining plate
(S).



Dismantle the pressure branch (700).



Dismantle the segment retainer (671) on
the pressure branch (700).



Remove the O-ring (731) from the centring
recess on the pressure branch (700).



Fit rotor (600) with protective cover (SH).



Prop up the rotor (600) with lining plate
(S).



For shaft seals with cartridge units, see
chapter 9.4 of the operating and assembly
instructions for instructions on how to dis-
mantle the shaft seal.



Remove the suction casing (500).

Summary of Contents for BN 100-6LS







































































Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands

Seepex BN 100-6LS, Operating And Assembly Instruction Manual

Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands