Seepex BN 100-6LS Operating And Assembly Instruction Manual Download Page 30

Page: 30 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

2 (18)

Dismantling/reassembly

9.1.1.3 Rotor (600) - dismantling



Remove upper adjusting segments
(635.o).

–

Conveying product can escape.

Pump with dry-running protection option
(TSE)



Mount self-tapping screws (658) and hold-
ing device (657).



Remove upper half of the stator (601.o).

–

Conveying product can escape.



Dismantle adjusting segments (635.u).

–

Secure adjusting segments (635.u) to
prevent them from falling down.



Remove lower half of the stator (601.u)
smoothly.

–

Conveying product can escape.

Tool (W29/lifting equipment incl. lashing strap)



Secure rotor (600).

–

Use tool (W29).

Summary of Contents for BN 100-6LS







































































Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands

Seepex BN 100-6LS, Operating And Assembly Instruction Manual

Search results

Summary of Contents for BN 100-6LS

Reviews:

Related manuals for BN 100-6LS

Brands by name

Popular brands