background image

ENFORCER SLI 820R/-4

 Tech Manual

Page 17

(4) Within 15 seconds, push any button of

the first transmitter to be learned.  At this

time, all previous codes are deleted, and

the alarm learns this transmitter's code.

1 chirp confirms code is learned.  (If no

button is pressed within this 15-second

period, code learning is exited, and old

codes are retained.)

(5) Within 15 seconds, push any button of

the second transmitter to be learned (if

applicable).  1 chirp confirms learned.

(6) Repeat step (5) until all transmitters are

learned.  The siren chirps once for each

transmitter when its code is successfully

learned.

B. Exit the code learning procedure — The

alarm chirps the siren two times, exits the

code learning mode, and is disarmed after

learning the fourth transmitter's code, or if

you turn the ignition switch ON, or if you do

nothing for 15 seconds.

Note – This section applies only if the optional

ENFORCER remotes are used.
The alarm can learn a max. of 4 remotes.  RF

Code Wash™ deletes all previous remotes when

any new remote is learned.  This prevents

unauthorized use of lost or stolen transmitters,

and, because the user's transmitter no longer

works, alerts the user if someone has secretly

code learned a new transmitter.  However, it also

means that, when code learning is being done,

ALL THE USER'S TRANSMITTERS MUST BE CODE

LEARNED AT THE SAME TIME.
A. Procedure:

(1) Disarm the alarm.
(2) Turn ignition switch ON, then OFF, then

ON, then OFF.

(3) Press the VEPLe button three times within

15 secs. of turning the ignition OFF.  The

siren chirps once.

Table B — Chart of VEPLe button operations:

VEPLe BUTTON (push-button)

CODE LEARNING

The VEPLe button is a 4-function push-button

switch.  It is used for entering and exiting the

valet mode, emergency disarm, programming,

and code learning.

Table B shows how the VEPLe button is used.

Enter polarity learn mode
Disarmed
Turn ON
Within 15 sec. press and

hold VELPe switch for 4 sec.
Chirp once

The alarm is now in the

polarity learn mode
OFF
Turn ignition OFF to exit

polarity learn mode, siren

will chirp twice

Step

Initial status
Ignition sw.
VEPLe button

Siren/light

confirm

Status

LED
Note

Exit valet mode
Valet mode
Turn from OFF to ON
Press 3 times within

15 sec. of ignition ON
Chirp twice and flash

twice after VEPLe

pressed 3rd time
The alarm is now

disarmed
OFF

E: Emergency disarm

Armed or triggered
Turn from OFF to ON
Press 3 times within

15 sec. of ignition ON
Chirp 3 times & flash

3 times after VEPLe

pressed 3rd time
The alarm is now in

the valet mode
Slow flashes
Procedure is the same

as valet mode

Enter Valet mode
Disarmed
Turn from OFF to ON
Press 3 times within

15 sec. of ignition ON
Chirp once and flash

once after VEPLe

pressed 3rd time
The alarm is now in

the valet mode
Slow flashes

Enter code learning
Disarmed
Turn ON/OFF/ON/OFF
Press 3 times within 15

sec. of ignition OFF
Chirp once after VEPLe

pressed 3rd time

The alarm is now in the

code learning mode
OFF
Inactivity for 15 seconds

will exit code learning

mode

V: Valet mode enter and exit

Disarmed
Turn ON/OFF
Press 3 times within 15

sec. of ignition OFF
Chirp once after both

pressing VEPLe 3 times

and turning ignition ON
The alarm is now in the

programming mode
OFF
Inactivity for 15 sec.  will

exit programming mode

L: Learning

P: Programming

Summary of Contents for Enforcer SLI 820A





















Reviews: