background image

008 Sears CA Treadmill Service Manual [rev 1.0]  |  

Section Two | 

Horizon Fitness “-Step” Diagnostic Process

120

 VAC 

 

>>

 Horizon Fitness “5-Step” Treadmill Diagnostic Process

Step 1 | 

 Proper supplying power to treadmill.

 

• Make sure the treadmill is not on an extension cord, surge protector or GFCI circuit.  Extension

 

   cords and surge protectors create energy loss, which prevents proper voltage from being 

 

   supplied to the treadmill.

 

• Make sure the treadmill is on a dedicated circuit.  Horizon Fitness recommends a 20 amp 

               dedicated circuit, but a 15 amp dedicated circuit may be sufficient.

 

• Make sure that proper voltage is being supplied from the wall outlet. 

 

• Disconnect the treadmill power cord from the wall outlet.  Using an AC voltmeter, verify that the 

               proper AC voltage is present at the wall outlet.  Nominal 120 volts AC may vary between 
 

   approximately 105 volts AC and 135 volts AC.  If the AC voltage is missing or incorrect, check    

  

   the AC service or consult an electrician.  

The following steps are provided as routine checkpoints when diagnosing problems on 
a Horizon Fitness treadmill.  If followed correctly, these checkpoints should help diagnos 
the majority of problems that may be encountered.

WARNING

 Hazardous voltages will be tested in the following procedure. Exercise extreme caution 
when performing these procedures.  Do not connect or disconnect any wiring, 
connectors, or other components with the power applied to the treadmill.

Step  | 

 Proper Wiring

 

• Verify that all wires are secure and attached in the correct position. 

 

• Verify that there aren’t any pinches or cuts in any of the wires, especially the console cable 

               connecting from the motor control board to the upper board.  Replace any wires that are 
               pinched or cut.

Summary of Contents for 30727














































Reviews: