manualshive.com logo in svg

Sears 30727, Service Manual

Share
Download
Sears 30727 Service Manual Download Page 34

 

 |  008 Sears CA Treadmill Service Manual [rev 1.0]

Section Three | 

Troubleshooting

Treadmill Troubleshooting

 

>>

 Heart Rate

Symptom

Possible Cause

Test Procedure

Repair

Heart rate erratic.

User error.

Reference Proper Heart 
Rate Usage p11.

Failed heart rate 
receiver.

Reference Proper Heart 
Rate Usage p11.

If proper heart rate 
instructions are followed 
and heart rate continues 
to be erratic, replace 
heart rate receiver.

Failed upper board.

Reference Proper Heart 
Rate Usage p11.

Replace upper board. 

No heart rate function. 
(Hand Grips)

Failed heart rate grips.

Reference Proper Heart 
Rate Usage p11.

If there is absolutely no 
heart response, replace 
heart rate grips.

Heart rate erratic.

User error.

Reference Proper Heart 
Rate Usage p23.

Electromagnetic 
interference.

Check immediate area 
for causes of 

interference: florescent 

lighting, electric dog 
fences, large electric 
motors, etc..

Remove interference 
from vicinity of the unit.

Summary of Contents for 30727














































Reviews:

No comments

Brands by name

Popular brands

Load more brands