Seaboater 100 Specifiations Download Page 46

Page: 46 / 55

All exterior hatches, companionways and locker doors shall be provided with a means
of secure closure to prevent unauthorized access. A lock system shall be provided for
the companionway and the crew cabin forward.

11.2. Winches

The following Lewmar winches are to be used:

Primaries

2 x Lewmar 111/3AHST

Secondaries/Halyard

2 x Lewmar 66/3AHST

Main Halyard Winch

1 x Lewmar LMS600 (Subject to review with
Sparmaker)

Mainsheet (Reel Winch) 1 x Lewmar LMS600

11.3. Deck Hardware

The following Lewmar deck hardware is to be used:

Qty

Part No.

Description

Mainsheet

Single part mainsheet dead-ended on boom from Hydraulic reel
winch in fwd end of aft cockpit.

Genoa 110%, Tracks, Cars and Footblocks

2991 7300

Size 3 Racing Track 1.75m Long

2990 5300

End Stop, at Aft End of Track.

2990 5301

End Stop with Control Line and Becket, 2:1 Purchase.

2990 5312

Plunger Stop

2990 3351

Port Side Genoa Car

2990 3352

Stb Side Genoa Car

2990 6131

130mm Footblock, Single Sheave

Asymetrical

2990 1131

130mm Single Block for Sheet
Tack attached to Sprit End with Strop

Rondal
623030

Removable Screw in Pad Eye & Base for Sheet Blocks

Mast Base Blocks

2990 2100

105mm Fixed Halyard Block for Masthead Spin Halyard

2990 2100

105mm Fixed Halyard Block for Main Halyard & Spare Main
Halyard

2990 2100

105mm Fixed Halyard Block for Genoa & Fractional Spin Halyard

2990 2100

105mm Fixed Halyard Block for Staysail

2990 2100

105mm Fixed Halyard Block for Reefs

Snatch Blocks

19 8505 00

125mm Snatch Block

Pad Eyes

Rondal
623030

Removable Screw in Pad Eye & Base for 2 Pairs at Rail for
Barberhauling Genoa and a 1 Pair Just Fwd of Spin Sheets

Summary of Contents for 100
























































Search results

Summary of Contents for 100

Reviews:

Related manuals for 100

Brands by name

Popular brands

Seaboater 100, Specifiations

Search results

Summary of Contents for 100

Reviews:

Related manuals for 100

Brands by name

Popular brands