Seaboater 100 Specifiations Download Page 41

Page: 41 / 55

Distribution circuit breakers.

Fisher Panda gauge and control panel.

Tank Tender (non-electric).

Fuel pump “run” indication.

Bilge pump “run” indicators.

Aft tank grey water manual pump control & indicator.

Aft black water manual pump control & indicator.

Fwd black water manual pump control & run indicator.

Fwd tank grey water manual pump control & run indicator.

Alarm panel

Exterior light switching.

Navigation lantern switching and indication.

Windex light switch.

Spreader light switches (x2).

Helm Pedestal/Cockpit Side Panel

Main engine panel - stop/start station with gauges & buzzer.

A DC outlet for hand held spotlight.

Ritchie compass complete with illumination and dimmer.

Bow thruster controls.

Radar

B&G Autopilot.

B&G FFD

B&G Analog 360

10.10. Electrical Equipment Lists

All instruments and equipment located at the chart table area and steering pedestals are
to be fitted with dimmer controlled illumination.

The following is a list of equipment to be installed, for make and model see relevant
section in this specification:

AC Equipment

Supplied By

AC Outlets

Btcino

Air Conditioning

Frigomar

Galley Freezer

Frigomar

Galley Refrigerator

Frigomar

Watermaker

HEM

Microwave Oven

Miele

Battery Chargers

Mastervolt

Entertainment Systems

Various

Washer / Dryer

Miele

Water Heater

Attwood

Trash Compactor

Broan-Nutone

DC Equipment (24 volt)

Supplied By

Auto Pilot

B&G

Engine Room Vent Fan

Par/Jabsco

Fwd & Aft Black Water Pumps (x2)

G&R

Fwd & Aft Grey Water Pumps (x2)

G&R

Bilge Pump (Primary)

G&R

Summary of Contents for 100
























































Search results

Summary of Contents for 100

Reviews:

Related manuals for 100

Brands by name

Popular brands

Seaboater 100, Specifiations

Search results

Summary of Contents for 100

Reviews:

Related manuals for 100

Brands by name

Popular brands