background image

Chart Table &
Passage
Stbd Guest Cabin
Stbd Guest Heads
Port Guest Cabin
Port Guest Heads
Engine Room
Machinery Room
Lazarette

Totals

3

2

4

2

2

2

1

2

3

2

2

1

2

2
2
2

25

5

11

16

8

23

6

Switches and Receptacles

All interior switches, rheostats, etc., shall be BTicino, or equal as selected by the Owner.
All exterior switches to be watertight, Carling, or equal All interior receptacles shall be
BTicino, or equal, duplex type. All head and galley receptacles to be ground fault interrupt
type. All exterior, fore peak, lazarette and engine room receptacles to be watertight, single
receptacle. All exterior DC receptacles to be watertight with screw caps.

Switches/Receptacles Required:

Functions to be discussed with Owner.

Switches/Receptacles Required

Function

Standard
On/Off
Switch

Dimmer
Non-Latch
ing Switch

2/3 Way
Switch

A/C
Switch/
Controls

220V

Socket &

Plug

24V

Socket &

Plug

Face

Plate &

Mounting

Grid
(Module)

Shaving

Socket &

Mounting

Grid

Make & Model

Crew Cabin

1

1

1

1

Crew Heads

1

1

1

Owners Cabin

12

1

1

1

3

Owners Heads

2

2

1

Saloon

6

6

1

1

3

Galley

2

2

2

Chart Table &
Passage

1

4

1

1

2

Stbd Guest Cabin

2

1

1

1

Stbd Guest
Heads

2

1

Port Guest Cabin

2

1

1

1

Port Guest Heads

2

1

Engine Room

1

1

1

2

Machinery Room

1

1

1

1

Lazarette

1

Totals

18

6

22

4

10

5

19

4

10.13. Navigation Lights & Outlets

Builder supplied navigation lights are to comply with the regulations of the country of
registry and shall be as specified.
Builder to supply a portable, plug-in DC powered searchlight, Guest No. 220 300,000
candlepower, or equal.
Navigation and deck lights to be switched from the main switch panel.

44

Summary of Contents for 100
























































Reviews: