background image

FEATURES AND SPECIFICATIONS

respectively 6m, 7 m and 

Hydraulic locking is guaranteed on gates with length up to 1.80 m with the Half Tank 270 and Mini Tank operators 
while for lengths up to 2.20 m use the Half Tank 390. An electric lock should be used for leaves (in all versions) 
exceeding those lengths.

T

he 

HALF TANK 270

,

 HALF TANK 390

 and 

MINI TANK

 are high quality hydraulic operators for residential and 

condominium use with leaf length up to 

3 m.

 Available in the following versions:

AC

 

(with lock in opening and closing position) 

SC 

(with lock only in closing 

)

SA 

(with lock only in opening 

 ) 

SB

 

(without lock)

 

The Half Tank 270-390 and Mini Tank are supplied with by-pass valves for the power regulation in both opening and 
closing. Electronic adjustable slow down in opening and closing with control board. For the European laws and 
directives actually in force it is strongly recommended to use the Safety Gate (device for the reading of the gate 
position), for reverse in case of obstacle. 

position

position

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

67411170

17

7

7

8

8

9

9

6

6

5

5

10

10

1

1

3

3

4

4

2

2

Fig. 3

Dimensions (

mm

)

     Half Tank 270
(*) Half Tank 390 

Fig. 1

96

70

0

/

4 *

1 00

  12

0

7

2 0 / 

390*

05

 12

0*

1

0 /

9

x

y

Note: 

Version with brake in closing 

+ 25 mm in x and y.
Version with brake in opening and 
c 50 mm in x and y.

Fig. 2

Note: 

Version with brake in closing 

+ 25 mm in x and y.
Version with brake in opening and 
c 50 mm in x and y.

Dimensions (

mm

)

Mini Tank

70

90

2 0 

7

995

1060

x

y

1

    Rod cover extrusion 

2

    External lock attachment

3

    Front fixing  

4

    Rear bracket fixing plate 

5

    Hydraulic cylinder 

6    

By-pass valves 

7

    Electric motor

   Hydraulic pump 

9

    Electric cable exit

10

  Release key  

     

HALF TANK - MINI TANK

English

English

REV 06 - 03/2015

Summary of Contents for HALF TANK

























Reviews: