Sea-Bird Scientific SBE 33 Product Manual Download Page 4 | Manualshive

Page: 4 / 55

background image

Manual revision 017

Table of Contents

SBE 33

4

Table of Contents

Limited Liability Statement ................................................................ 2

Declaration of Conformity .................................................................. 3

Table of Contents ................................................................................. 4

Section 1: Introduction ........................................................................ 6

About this Manual .............................................................................................6

Unpacking SBE 33 .............................................................................................7

Section 2: Description of SBE 33 ........................................................ 8

System Description ............................................................................................8

Specifications ................................................................................................... 11

PDIM Dimensions and Connectors .................................................................. 12

SBE 33 Front Panel .......................................................................................... 13

SBE 33 Back Panel .......................................................................................... 13

Cables and Wiring ........................................................................................... 14

System Communications ................................................................................. 17

NMEA and Surface PAR ................................................................................. 18

Section 3: Setting Up System............................................................. 20

Installing Software ........................................................................................... 20

Setting CTD Baud Rate and Operating Parameters ......................................... 21

V2), 25 (not 25

), or 49 ........................... 21

.......................................................................... 23

Setting Up and Testing System ........................................................................ 24

Changing Communication Settings between SBE 33 and Computer .............. 27

Checking CTD Configuration (.xmlcon or .con) File in Seasave .................... 28

Section 4: Mounting and Wiring System ......................................... 29

Cable, Winch, and Deck Gear (not supplied by Sea-Bird) .............................. 29

Mounting SBE 33 ............................................................................................ 29

Wiring System ................................................................................................. 30

Water Sampler or PDIM to CTD .............................................................. 30

Sea Cable from SBE 33 to Water Sampler or PDIM ................................ 30

SBE 33 to Computer ................................................................................. 30

Power to SBE 33 ....................................................................................... 31

NMEA Navigation Device to SBE 33 ...................................................... 31

Surface PAR Sensor to SBE 33 ................................................................ 31

Section 5: Operating System ............................................................. 32

Acquiring Real-Time Data and Firing Bottles from Seasave ........................... 32

Firing Bottles from SBE 33 Front Panel .......................................................... 36

Recovering CTD and Water Sampler .............................................................. 37

Uploading CTD Data from Memory ................................................................ 38

Processing Data Using SBE Data Processing .................................................. 38

Editing Raw Data File ...................................................................................... 39

Section 6: Routine Maintenance ....................................................... 40

Connector Mating and Maintenance ................................................................ 40

Cleaning SBE 33 Deck Unit ............................................................................ 40

Section 7: Troubleshooting ................................................................ 41

Problem 1: Unable to View Data in Seasave (Real-Time Data Acquisition
program) .......................................................................................................... 41

Problem 2: SBE 33 Completely Inoperable ..................................................... 41

Problem 3: Water Sampler or CTD Does Not Respond ................................... 42

«
...
2
3
4
5
6
...
»

Summary of Contents for SBE 33
























































Reviews:

No comments

Related manuals for SBE 33

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: Vahle Pages: 96

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: Warehouse-lighting Pages: 3

Brand: E2S Pages: 5

Brand: Major Pages: 52

Brand: Hammer Strength Pages: 18

Brand: Konica Minolta Pages: 32

Brand: Tascam Pages: 78

MINISTUDIO CREATOR US-42

Brand: Tascam Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands