Scotsman CME1386 User Manual Download

Page: 42 / 46

Service Diagnosis

Eclipse

1300, 1600

September 2003

Page 42

Problem or Symptom

Possible Cause

Probable Correction

Low capacity

Dirty condenser

Clean condenser

Air temperature intake to condenser
very high

Re-orient condenser to avoid hot air
intake

Water temperature intake to ice making
section very high

Check for hot water supply to ice
machine due to mal-functioning or
non-existent hot water check valve at
dishwashing sink

False bin full - bin full light is ON and the
bin is not full

Unplug thermostat from terminal 7 and
check controller. Bin full light must go
out within 4 minutes or ice sensors need
checking.

Check ice sensors for proper position

Check ice sensors for scale build up

Storage bin or dispenser not holding ice
properly

Check drains for water flow from ice
machine (separate to correct) or
restriction

High volume of drinks dispensed, cold
plate melting ice

Suggest pre-cooler for water supply to
cold plate

Vapor inlet valve leaks through slightly
during the freeze cycle

Check valve body for similar
temperatures on inlet and outlet, the
outlet should be colder and frost
develops on the tubes to the
evaporators

Splash shield missing/out of position
and water is cascading out of the
reservoir

Install or re-secure splash shield. Check
water distributors for proper attachment.

Exceeding maximum freeze time,
compressor unit trips on high discharge
temp

Check condenser bypass valve

Poor ice formation - very cloudy
and misshapen

Dirty water system

Clean the water distributors and the tops
of the evaporators to remove built up
mineral scale

Low refrigerant charge.

Add several pounds of refrigerant to
check. If low on charge, locate leak.
Recover refrigerant, repair leak, replace
drier, evacuate to 300 microns and
weigh in the nameplate charge.

Whistling noise at CP unit during
harvest

By pass and liquid inlet valve coils not
getting power

Check harness

Summary of Contents for CME1386















































Search results

Summary of Contents for CME1386

Reviews:

Related manuals for CME1386

Brands by name

Popular brands

Scotsman CME1386, User Manual

Search results

Summary of Contents for CME1386

Reviews:

Related manuals for CME1386

Brands by name

Popular brands