Scotsman CME1386 User Manual Download | Manualshive

Page: 36 / 46

background image

Other Maintenance

The remote air cooled condenser coil must be
cleaned occasionally to keep the system operating
at high efficiency.

·

Remove any large debris from the outside of the
coil.

·

Vacuum accumulated dust.

·

Wash out the coils with water.

Caution: Do NOT use excessive water pressure as
that will bend the fins.

·

Straighten any damaged fins with a fin comb.

·

If the coils have become coated with grease, a
coil cleaner will have to be used to wash the
coils.

Disconnect power to the condensing unit and
remove the condenser top.

·

Inspect the fan blade to be sure it is not cracked
and is clean.

Return the condenser top to its original position
and reconnect the power supply.

Eclipse

ä

1300, 1600

September 2003

Page 36

Moving Parts Hazard

Rotating fan blade can
cause cuts

Disconnect electrical
power before removing
condenser top or fan
guard.

«
...
34
35
36
37
38
...
»

Summary of Contents for CME1386















































Reviews:

No comments

Related manuals for CME1386

Brand: LabelTac Pages: 28

Brand: Gaggia Pages: 4

PerfectCoffee MC06

Brand: Waeco Pages: 88

Brand: GE Pages: 14

Brand: Schaerer Pages: 34

Brand: Hoshizaki Pages: 33

CafeRomatica NICR7

Brand: Nivona Pages: 27

Brand: Witt Pages: 132

Brand: Dolce Gusto Pages: 20

Brand: Mistral Pages: 28

Brand: U-Line Pages: 36

Brand: Westfalia Pages: 18

Brand: ECM Pages: 22

Brand: Hoshizaki Pages: 22

Brand: Milu Pages: 23

Brand: Gaggenau Pages: 24

Brand: Duronic Pages: 52

Brand: Virgo Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands