Scotsman CME1386 User Manual Download

Page: 1 / 46

Introduction:

This manual covers the assembly, installation, start
up, operation and maintenance of the 1300 and
1600 remote low side cuber systems.

An illustrated parts list and wiring diagram is in the

center of this manual.

Keep this manual for future reference.

Eclipse

1300,1600

September 2003

Page 1

Table of Contents

Introduction: · · · · · · · · · · · · · · · · · · Page 1

Configuration: · · · · · · · · · · · · · · · · · Page 2

Technical Specifications · · · · · · · · · · · · Page 3

Model Number Locations · · · · · · · · · · · Page 4

Cabinet Drawings, Ice Making System · · · · Page 5

Cabinet Drawings, Compressor Package and
Condensers · · · · · · · · · · · · · · · · · · Page 6

Proper Combinations: · · · · · · · · · · · · · Page 7

Create the System· · · · · · · · · · · · · · · Page 8

System Examples · · · · · · · · · · · · · · · Page 9

System Examples · · · · · · · · · · · · · · · Page 10

Place Remote System · · · · · · · · · · · · · Page 11

System Location · · · · · · · · · · · · · · · · Page 12

Route Tubing · · · · · · · · · · · · · · · · · Page 13

Ice Making Section · · · · · · · · · · · · · · Page 14

Compressor Package · · · · · · · · · · · · · Page 15

Condensing Section Assembly · · · · · · · · Page 16

Condensing Section Assembly · · · · · · · · Page 17

Ice making section: · · · · · · · · · · · · · · Page 18

Bin Thermostat - Routing · · · · · · · · · · · Page 19

Bin Thermostat - Bracket & Bulb · · · · · · · Page 20

Water and Drain · · · · · · · · · · · · · · · · Page 21

Water and Drain · · · · · · · · · · · · · · · · Page 22

Ice Making Section Set Up · · · · · · · · · · Page 23

Coupling Connections: · · · · · · · · · · · · Page 24

Condensing Unit Connections · · · · · · · · · Page 25

Final Placement · · · · · · · · · · · · · · · · Page 26

Controller Operation · · · · · · · · · · · · · · Page 27

Initial Start Up - 1300 and 1600 · · · · · · · · Page 28

Purge Adjustment · · · · · · · · · · · · · · · Page 29

System Operation:· · · · · · · · · · · · · · · Page 30

Refrigeration Details: · · · · · · · · · · · · · Page 31

Technicians Only: Freeze Cycle Sequence of Operation

· · · · · · · · · · · · · · · · · · · · · · · · · Page 32

Technicians Only: Harvest Cycle Sequence of
Operation · · · · · · · · · · · · · · · · · · · Page 33

Power and Water Interruptions · · · · · · · · Page 34

Sanitation and Cleaning · · · · · · · · · · · · Page 35

Other Maintenance · · · · · · · · · · · · · · Page 36

Water Distributors · · · · · · · · · · · · · · · Page 37

Ice Sensors · · · · · · · · · · · · · · · · · · Page 38

Water Level Sensor Maintenance · · · · · · · Page 39

Service Diagnosis · · · · · · · · · · · · · · · Page 40

Service Diagnosis · · · · · · · · · · · · · · · Page 41

Service Diagnosis · · · · · · · · · · · · · · · Page 42

Controller Features & Last Error Recall · · · · Page 43

Operational Characteristics 1300 lb system · · Page 44

Operational Characteristics 1600 lb system · · Page 45

Refrigeration System Service · · · · · · · · · Page 46

Note this symbol when it appears. It

indicates a potential hazard.

Summary of Contents for CME1386















































Search results

Summary of Contents for CME1386

Reviews:

Related manuals for CME1386

Brands by name

Popular brands

Scotsman CME1386, User Manual

Search results

Summary of Contents for CME1386

Reviews:

Related manuals for CME1386

Brands by name

Popular brands