Schlumberger CAMERON LEDEEN VA Series Installation, Operation And Maintenance Manual Download Page 20 | Manualshive

Page: 20 / 42

background image

19

Figure 1

When the end cap seal need to be replaced (DA & SR) follow the instructions below:(see fig. 2)

1.

Place the actuator in fail safe position.

2.

Remove any electric power and pressure supply.

3.

Unthread the lock nut (item 36) and the stop screw (item 35) paying attention to not remove completely
the end stroke.

Warning:

Remember that a preloaded spring is included in the cylinder. (If SR Actuator)

4.

Unthread the screws (item 45) with washer (item 46) in the proper sequence and remove the end flange
(item 32) along with end stroke assembly.

5.

Remove the circlip (item 33) which holds the end stroke screw (item 35).

6.

Remove the end stroke screw (item 36) with locking nut (item 35) from end flange. Then remove the
locking nut from the end stroke screw.

7.

Remove the existing O-ring (item 34) and clean the groove of the locking nut.

8.

Clean the surface of the end flange (item 32) of the cylinder.

9.

Install the new O-ring on locking nut and apply a grease film.

(suggested grease: Parker super-o-lube or equivalent)

10.

Install the locking nut into the stop screw and thread the stop screw assembly into the end flange and lock
it with circlip.

«
...
18
19
20
21
22
...
»

Summary of Contents for CAMERON LEDEEN VA Series











































Reviews:

No comments

Related manuals for CAMERON LEDEEN VA Series

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: Samson Pages: 6

Brand: M-system Pages: 13

STRATOSTM INSPIRE

Brand: Ultrahaptics Pages: 7

Brand: LAUNDRY SOLUTION Pages: 14

Brand: C&C Pages: 17

Brand: Genius Pages: 52

Brand: Barco Pages: 2

Princeton Applied Research PARSTAT 2273

Brand: Ametek Pages: 26

Brand: CSA Pages: 12

Brand: PRECISION DIGITAL Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands