23
GB
1. Introduction
Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare parts,
•
Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating
the machine and carefully follow its information. The
machine can only be operated by persons who were
instructed concerning the operation of the machine
and who are informed about the associated dangers.
The minimum age requirement must be complied
with. In addition to the safety requirements in these
operating instructions and your country’s applicable
regulations, you should observe the generally rec-
ognized technical rules concerning the operation of
woodworking machines.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these in-
structions and the safety instructions.
2. Device description (Fig. 1-18)
1 Case door
2 Door lock
3 Saw blade safety device
4 Saw blade guidance
5 Longitudinal limit stop
6 Table width enlargement
7 Tabletop
8 Clamping lever
9 Frame
10 On/Off switch
11 Handle for saw blade tensioning
12 Handle for belt tensioning
13 Adjustment handle for sawblade guard
14 Mitre gauge (not shown / optional accessory)
15 Underframe
3. Scope of delivery
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal
-
lowing and suffocation!
• Bandsaw
• Saw table
• Retainer plate
• Rail with scale
• Push stick
• Guide rail for lengthwise aligning stop
• Longitudinal limit stop
• Allen key (3x)
• Screwdriver
• Open-ended spanner (2x)
• Cross member, top (2x)
• Longitudinal member, top (2x)
• Cross member, bottom (2x)
• Longitudinal member, bottom (2x)
• Foot strut (4x)
• Table width enlargement with guide rail for length-
wise aligning stop
• Fastening materials
• Original operating instructions
Summary of Contents for 5901505850
