background image

 

22 

 
5.

 

SAFETY WARNINGS. 

 

 

Don’t open the pump box if the power is on. 

 

 

Do not touch the pump  (which can reach high temperatures) when the plant is functioning. 

 

 

Do not locate the pump  near objects either inflammable or that can deteriorate if exposed to 
high temperature. 

 

 

Check if the watermaker is correctly installed eventually  contacting a Schenker service point. 

 

 

Verify that the hoses used for installation are in keeping with the indicated specifications.    

 

 

The water produced using clean sea water will have an average quality of 500-600 ppm TDS. 
Unless the correct cleaning procedures are carried out in accordance with this manual, there 
may be bacteria present in the produced water. Therefore avoid drinking the water produced 
by the plant if an UV sterilizer has not been installed. 

 

 

Avoid using the plant where water is polluted (ports, or close to built-up areas, etc.) 

 
 

 

Children and inexperienced people shall not touch or operate the plant. 

 

 

Check periodically that no leakage is present. Do not switch on the plant when the boat is un-
attended. Avoid installing the plant where an eventual leakage may cause damages and jeop-
ardize the safety of the boat. 

 

 

Unqualified and non-Schenker personnel shall not perform any maintenance work. 

 
6.

 

WARRANTY 

 
The equipment and the relevant accessories are guarantee 12 months starting from the date on the de-
livery  document  of  the  merchandise.  The  guarantee  does  not  include  expendable  materials  (car-
tridges, active-carbon filters, membranes, etc.). The “ERS” pressure amplification device is guaran-
teed 36 months, provided that the annual maintenance is performed in one of Schenker service point. 
The guarantee covers every fault or defect of materials and parts and it is limited to the replacement 
or repair of faulty parts. The expenses for the device disassembly and reinstallation on the boat and 
for the transport of the equipment from or to our Service Point or our  factory will be on customer ac-
count.  
The under guarantee delivered parts transport  will be at customer’s own risk. 
In  case  of  repairs  under  guarantee,  directly  performed  by  our  technicians  on  the  customer  boat,  the 
faulty parts replacement cost will be on Schenker account, while manpower and travel expenses will 
be charged  to the customer. The guarantee does not include the faults caused by negligence in operat-
ing, maintenance and installation of the device (if they are not performed by an authorised Schenker 
Service point). 
If  non-authorized  personnel  perform  the  disassembly,  every  obligation  of  this  guarantee  will  auto-
matically lapse. Schenker Italia can not be held liable for any direct or indirect damage caused by the 
malfunctioning  of  the  equipment,  limiting  its  responsibility  to  the  repair  and  replacement  of  faulty 
parts.

 

 

Summary of Contents for 100M220























Reviews: