background image

18

Situation: 18.07.2005

SDT-0018-02EN

Instruction Manual Control and Switch Panel DT 201 B

5.7.6

Tank alarm

If the water tank level falls below 12 % or if the waste water tank level exceeds 
87 %, the warning triangle, the word "ALARM" and the tank symbol flash in 
the basic display.

The tank symbol and the tank level percentage indicator also flash in the tank 
display.

„

Fill up water tank or drain waste water tank.

5.7.7

Step alarm

Before commencing the journey, the step must be retracted. If the step is not 
retracted, a loud warning signal is emitted and the buzzer symbol appears on 
the display when the engine is started.

If the sensors are defective or if the D+ signal is missing, the warning signal 
can fail. Before commencing the journey, the driver must therefore check if 
the step is retracted.

False step alarm

In exceptional cases, there can be a false alarm: The step alarm is triggered, 
even though the step is retracted.

If such a malfunction occurs, the acoustic warning signal can be switched off 
after starting the engine.

„

In the basic display, press the "MENUE" button for more than 3 seconds.

„

Set the buzzer to "OFF" with the "+" or "–" button of the basic menu.

„

Confirm the entry with "OK".

„

To exit the menu, press any button or wait for 20 seconds until the display 
automatically switches to the basic display.

„

Have the malfunction rectified by the dealer.

5.7.8

Mains alarm

If the 230 V power supply fails or if it is disconnected from the motorhome, the 
230 V symbol flashes.

As soon as the 230 V power supply has been restored, the symbol lights up 
and remains illuminated.

The symbol goes out as soon as the engine is started.

Switching off the flashing

symbol

„

Press "OK" button.
The mains alarm is confirmed. The symbol goes out.

W

If the water tank remains empty due to an external water supply, the tank 
alarm can be switched off.

W

For more information, see the section 5.5.

W

Before commencing the journey, check if the step is retracted.

W

The acoustic warning signal must be switched off after every engine start, 
until the malfunction has been rectified. 

Summary of Contents for DT 201 B

























Reviews: