background image

12

Situation: 18.07.2005

SDT-0018-02EN

Instruction Manual Control and Switch Panel DT 201 B

Charge request

CHARGE !

The batteries should be fully charged every 4 weeks for a long service life.

As a reminder a charge request is displayed 20 days after the last equalising 
charge. 

„

Connect the motorhome to the 230 V power supply.
The batteries are charged.

5.3.3

Displaying the solar current (optional)

Battery button

The solar current display is only possible with a solar charge regulator type 
LRS... of Schaudt GmbH.

„

Press battery button three times briefly.
The solar currents of living area battery and starter battery appear on the 
3rd page of the battery menu:

Solar current display of the living area battery

Solar current display of the starter battery

„

To exit the display, press any button or wait for 20 seconds until the dis-
play automatically switches to the basic display.

5.3.4

Displaying the maximum battery capacity of the living 
area battery

The maximum battery capacity of the living area battery "Ah max" is displayed 
in the battery menu, but it cannot be set. The maximum capacity is set at the 
factory to 80 % of the nominal capacity. The control and switch panel also 
recalculates the battery capacity after every complete charging cycle (total 
charge and total discharge) and indicates the current value. This display 
applies only to the living area battery.

„

Press battery button once briefly.

„

Press the "MENUE" button for more than 3 seconds.
The maximum battery capacity "Ah max" of the living area battery appears 
on the 1st page of the battery menu.

„

To exit the menu, press any button or wait for 20 seconds until the display 
automatically switches to the basic display.

W

For more information see section 5.7 as well as the instruction manual for 
the Electrobloc.

W

For more information, see the section 5.7.

Summary of Contents for DT 201 B

























Reviews: