IM022
SC-MG45M25
6
INSTRUCTION FOR USING
ASSEMBLING(Fig.1-7)
Place the head tightly onto the head inlet.
Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into
the motor housing.
Place the cutting blade onto the snake shaft with the blade facing the front as illustrated. Place
the desired cutting plate next to the cutting blade, fitting protrusions in the slots. If it is not fitted
properly, meat will not be ground.
Screw the fixing ring tightly. Do not overtighten.
Place the feed tray on the head and fix it into position.
Locate the unit on a firm surface.
The air passage at the bottom and the side of the motor housing should be kept free and not
blocked.
PROCESSING MEAT
Cut the meat into pieces so that they easily fit the throat.
Plug the meat grinder in and set the switch to the ON position.
Place the meat on the hopper tray and feed it into the meat grinder little by little with the pusher.
After finishing work switch off the meat grinder and unplug it from outlet.
MAKING KEBBE
Kebbe is a traditional Middle Eastern dish. It is usually prepared of lamb and bulgur minced
together to smooth paste. Paste is formed to hollow tubes, stuffed with mixture of meat and
spices and then deep-fried.
Feed the prepared minced meat through the kebbemaker.
Cut the resulting tube into cylinders of desired length.
Stuff the cylinders with filling and seal the ends.
Deep-fry kebbe.
MAKING SAUSAGES
Put the sausage skin in warm water for 10 minutes. Then slide the wet skin onto the sausage
horn.
Put the minced meat in the tray. To fill the skin push the meat into the cutter housing.
If the skin gets stuck onto the sausage horn, wet it with some water.
IMPLEMENTS FOR GRATING AND CHOPPING
These implements are used for chopping vegetables and fruit.
Insert the throat for grating and chopping into the socket located on the body. Fasten it by turning
counter-clockwise.
Fit any of the implements into the throat drum.
Insert the vegetables into the throat and push them using the pusher for grating and chopping.
REVERSE MODE
If the meat grinder is jammed, switch it off and without unplugging it from the outlet set the switch
to the R position.
The feed screw will start rotating in the opposite direction and push out jammed food.
If this does not help, unplug the meat grinder from the outlet, disassemble and clean it.
CLEANING AND MAINTENANCE
DISASSEMBLING
Switch off the appliance and make sure that the motor has stopped completely.
Unplug the appliance.
Disassemble by reversing the assembling steps.
CLEANING
Remove meat, etc.
Wash each part in warm soapy water.
Do not use abrasives, chlorine containing substances or organic solvents.
Do not immerse the motor housing in water, but only wipe it with a damp cloth.
The metal parts of the mincing machine are not to be washed in the dishwasher!
Do not wash all metal parts with hot water which temperature above 50
℃
. Bcs it will be
accelerate metal parts oxidation.
After washing pls use dry dishcloth clean the metal parts.
Summary of Contents for Silver Line SC-MG45M25
