83
MPS4232
Section 6: Maintenance
FTP://<IP address of the MPS>
<ENTER>
Drag and drop (or copy and paste) the RptXXX.csv to the
desktop for viewing. This must be repeated for every
module that was validated.
Performing a Single or Multi-Field Calibration-Valida-
tion
A Field Calibration-Validation (single or multi-unit) will
apply pressures from the calibrator at the current tempera-
ture of the modules, create and enable the field calibration
coefficients, and then auto-perform a validation. This
process allows for a single command to start a calibration
and validation without additional user input.
1. Follow the steps under Setup and Configuration.
2. [Optional] If a calibration-validation log is required
(for troubleshooting or requested by Scanivalve), start
an ASCII capture file using ScanTel:
File > Start ASCII Capture
Name the file and save in a directory.
3. To start an automated single unit field calibration-
validation, issue the command:
To start an automated multi-unit field calibration-valida
-
tion, issue the command:
<ENTER>
The Field Calibration-Validation (single or multi) will begin.
The process will stream information to the screen. When
completed, the MPS will return a completed message,
followed by a Prompt (>). If there is an issue, check the log
to find the error and correct any noted errors.
The calibration process will automatically enable the
field calibration coefficients (
) before the
validation. Once a Field Calibration-Validation is complete,
the field coefficients are stored in
.
5. Once the validation is completed, the report can be
found on the MPS’s system memory. Open a window in
“Windows Explorer” and in the address bar, type:
FTP://<IP address of the MPS>
<ENTER>
Drag and drop (or copy and paste) the RptXXX.csv to the
desktop for viewing. This must be repeated for every
module that was validated.
6. If the module passes validation; in ScanTel, issue the
command:
Saving the FC terms must be repeated for every module
that was calibrated (connect using ScanTel and issue
the command).
Performing a Manual Field Calibration or Validation
If a manual calibrator is to be used (non-Scanivalve cali-
brator), repeat the steps as show in the procedures
above, however replace the “
F
” variable of the CAL/VAL
commands with “
FM
”. The MPS will start the commanded
sequence and will instruct the user to apply pressure
manually, and input the pressure reading of the calibrator
at each pressure point.
Table 6-1: Recommended Cal/Val Settings
The following table shows Scanivalve’s recommended settings for MPS4232 Field Calibration and Validations.
Typical Full
Scale Range
Min Val
Pressure
Max Val
Pressure
Min Cal
Pressure
Max Cal
Pressure
Field Cal
Number of
Points
Field Val
Number of
Points
CALAVG
4” H2O
-0.145
0.145
-0.159
0.159
5 to 13
11 to 15
1 16
- or -
12 128
8” H2O
-0.289
0.289
-0.318
0.318
1 psid
-1
1
-1.1
1.1
5 psid
-5
5
-5.5
5.5
15 psid
-15
15
-16.5
16.5
50 psid
-15
50
-16.5
55
Summary of Contents for MPS4232
