background image

 

2

 / 

14

 

SC POWER SCB45PRO 

 Please charge the device for 24 hours before initial usage and recharge every 3 months 

to maintain good battery life. 

 Storage temperature at 3

to 40

 

ATTENTION!   

Neglecting these instructions & cautions below might cause personal injury and harmful or 
influence the function of the device.   

CAUTION: 

 

- Use the device exclusively for those purposes for which it is developed.   

- Do not use the device in rain or damp conditions. The functionality of device might be affected. 

- Keep the device away from inflammable material.   

- Always make sure the device is in a safe, solid condition!   

- The device should be stored in a safe & stable environment   

- Keep the device away from children & infirm person’s access.   

- Do not expose the device directly to solar radiation and / or other source of heat.   

- Never throw or drop this product to avoid causing damages.   

- The appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction. Children should be supervised to ensure that they do not play with the 
appliance. 

- If you do not plan to use the product, please disconnect DC connector of universal adaptor from 

the Mini Jump Start. The Mini Jump Start will change to power save mode to conserve the 
battery.   

- Never attempt to alter or disassemble the product. If there is a problem with the product please 

contact your dealer or place of purchase for further assistance. 

- Repairs and maintenance may only be accomplished by authorized specialists, who are familiar 

with the dangers/ regulations which go along with this equipment.   

- The Mini Jump Start must be recharged after the battery low voltage protection. 

 

Summary of Contents for SCB45Pro















Reviews: