background image

 

13

 / 

14

 

SC POWER SCB45PRO 

3.

 

In any case, if USB does not start properly, perhaps the current from external load is too low, please turn on the S.O.S. / 

LIGHT and try to reconnect again.   

4.

 

The device will be automatically shut down if none of operation and connection within 2 minutes. 

 

 

 

Recommendation:   

l

 

In case the extremely cold temperature is forecasted , please keep the device to be charged over-night in order to make sure 

the battery is fully charged . In case the ambient temperature is under -10

℃,

  it is recommended to connect the battery for 

3 minutes before jump start attempt . Further, we recommended that you connect the clips to disabled vehicle battery and 

turn the POWER on , then activate the JUMP START feature by depressing the Jump Start button (JUMP START red light on ) , 

then wait for 3-4 minutes prior to cranking the vehicle . This will help activate or “wam “ the disabled vehicle battery for best 

possible results . 

l

 

In some occasion , car engine may not be easier to start at first crank, so you are recommended to take several attempts (not 

more than 10 times ), as far as the inside battery have be warmed up , it can help to enhance the battery’s performance   

l

 

In order to keep the better performance of the device, it is recommended to be recharged in every 3 months, or it ought to 

be refreshed at least one time within 6 months. If battery is not recharged fully after use and also regularly maintained in a 

charged state at intervals stated above, then the device will not operate effectively if battery storage conditions were not 

followed as battery stored in discharged state will deteriorate quickly. 

l

 

The  device  will  be  protected  at  the  extremely  hot  circumstance,  so  it  is  not  recommended  to  store  inside  the  car 

compartment  during  the  summer  time,  and  not  to  be  recharged  at  higher  ambient  temperature.  (Please  refer  to  page  4 

point 4 of this user manual).

 

 

 

 

 

 

 

 

Summary of Contents for SCB45Pro















Reviews: