background image

 

10

 / 

14

 

SC POWER SCB45PRO 

 

ATTENTION! 

1.

 

The activity of engine cranking will be limited in 3 seconds, it will cut off automatically in case failed to ignite. After 15 seconds, 

resume again for next crank attempt (maximum of 10 times cranking is advised, otherwise the device might potentially be 

damaged.) 

2.

 

The car engine successfully started, please press the power button to turn off the device A.S.A.P. 

3.

 

Always re-charge the device after use and make sure it is fully re-charged before use.   

4.

 

When reverse polarity or excess 

its capability 

has occurred, the device will be automatically protected and all functions are 

terminated. The LED of light (white) and Booster (red) will flash alternately. Please turn off the device immediately, as long as 

the situation has fixed then turn on the power again to operate. 

 

OPERATION ON THE CAR WITH A DEAD BATTERY 

                                                                                Indication: 

                                                                                 

 

                                                                                                               

S.O.S / JUMP START RED LIGHT FLASH

 

Hold the Jump Start and Jump Start / S.O.S buttons simultaneously for 3 sec.

   

Please make sure the polarity is connected correctly before those buttons are pressed, otherwise the device will be severely 

damaged

 

ATTENTION:

 

1.

 

The car engine successfully started, please press the power button to turn off the device A.S.A.P. 

2.

 

The device will automatically shut down when idled after 1 minute. 

3.

 

Always re-charge the device after use or has it fully re-charged before use.   

4.

 

The device will be protected, if the drawn current excess its capability. Please turn off the device and then turn on the 

Summary of Contents for SCB45Pro















Reviews: