manualshive.com logo in svg

Sapling SDLG Series, Installation Manual

Share
Download
Sapling SDLG Series Installation Manual Download Page 40

40

The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

VERY IMPORTANT:

CONFIGURE THE MESSAGE DISPLAY BEFORE MOUNTING THE DISPLAY TO A WALL OR CEILING

A Sapling Master Clock and any Repeaters must be installed, powered, and set up 

BEFORE

 you attempt to set up a wireless clock system. If 

the Master Clock and Repeaters are not properly installed and powered, the secondary clocks will not synchronize.

Double Mount Installation

If any of the items listed in the kits are missing, you may contact your dealer and order a replacement kit.

Continued on next page

Description

SDLG Digital Clock

Digital Clock Wall Housing

6-19x1/2 screw

6-32x1 screw

Quantity

1

1

8

8

Picture

Included in Package

Included in Pole Kit (SAB-1BD-00S-0)

Dual-mount pole, including 
mounting plate

#10-32x3/8 green screw

#8-32x7/16 screw

1

1

8

Summary of Contents for SDLG Series






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands