Sanyo VHR-H772EV Service Manual Download Page 60

Page: 60 / 91

4-25

MECHANISM TROUBLESHOOTING GUIDE

In PB mode Tape Presence

not sensed.

Is the Pinch Roller attached

to the Capstan Motor Shaft?

Check Alignment positions

(page 4-14)

Does the T/Up

Reel turn?

Replace the Belt.

Is the Belt ok?

Does the Drum

Motor turn?

Are there DPG,

DFG Pulses?

Are the T/Up Supply Reel Sensors

ok?

Check Syscon,

Circuit.

Check Syscon,

Circuit.

Check Servo, Syscon.

Does the Capstan Motor turn?

Is the terminal voltage of the

Drum Motor more than 2.3V?

Replace the

Drum Motor.

Is the Vcc voltage of the Drum

Motor normal?

Check the clutch and the Idler

Assembly.

YES

Is the terminal voltage of Capstan

Motor supplied more than 4V?

Replace the

Capstan Motor.

Is the Voltage supplied to the

Capstan Motor Vcc1,Vcc2 each?

YES

Check Servo,

Power.

Summary of Contents for VHR-H772EV




























































































Search results

Summary of Contents for VHR-H772EV

Reviews:

Related manuals for VHR-H772EV

Brands by name

Popular brands

Sanyo VHR-H772EV, Service Manual

Search results

Summary of Contents for VHR-H772EV

Reviews:

Related manuals for VHR-H772EV

Brands by name

Popular brands