Sanyo VHR-H772EV Service Manual Download | Manualshive

Page: 52 / 91

background image

DECK MECHANISM ADJUSTMENT

4-17

Purpose: To obtain compatibility with other VCR(VCP) Models.

5-2. Confirm that the Tape passes smoothly

between the Take-up Guide and Pinch
Roller(using a Mirror or the naked eye).

1)

After completing Step 5-1.(Preliminary Adjustment),
check that the Tape passes around the Take-up Guide
and Pinch Roller without Folding or Curling at the Top or
Bottom.
(1) If Folding or Curling is observed at the Bottom of

the Take-up Guide then slowly turn the Tilt
Adjustment Screw(C) in the Clockwise direction.

(2) If Folding or Curling is observed at the Top of it then

slowly turn the Tilt Adjustment Screw(C) in the
Counterclockwise direction.

Check the RF Envelope after adjusting the A/C Head, if
the RF Waveform differs from Fig. C-5-4, performs
Precise Adjustment to flat the RF Waveform.

Test Equipment/ Fixture

• Oscilloscope
• Alignment Tape(SP)
• Screw ) Type 5mm

Connection Point

• Audio output jack

Test Conditions

(Mechanism Condition)

• Play an Alignment Tape

1KHz, 7KHz Sections

Adjustment Point

• Azimuth Adjustment Screw(A)
• Height Adjustment Screw(B)

1) Connect the Probe of the Oscilloscope to Audio Output

Jack.

2) Alternately adjust the Azimuth Adjustment Screw(A) and

the Tilt Adjustment Screw(C) for Maximum Output of the
1Khz and 7Khz segments, while maintaining the flattest
Envelope differential between the two Frequencies.

Adjustment Procedure

5-3. Precise Adjustment (Azimuth adjustment)

6. X-Value Adjustment

Fig. C-5-4

1KHZ

• Oscilloscope
• Alignment tape(SP only)
• Screw ) Type 5mm

• CH-1: PB RF Envelope
• CH-2: NTSC: SW 30Hz

PAL: SW 25Hz

• Head Switching Output

Test Point

• RF Envelope Output Test

Point

Test Conditions

(Mechanism Condition)

• Play an Alignment Tape

Adjustment Point

Connection Point

Test Equipment/ Fixture

Adjustment Procedure

1) Release the Automatic Tracking to run long enough for

Tracking to complete it’s Cycle.

2) Loosen the Fixed Mounting Screw and move the Base

Assembly A/C Head in the direction as shown in the
Diagram to find the center of the peak that allows for the
maximum Waveform Envelope.
This method should allow the 31um Head to be centrally
located over the 58um Tape Track.

3) Tighten the Base Assembly A/C Head mounting Screw.

7KHZ

A:Maximum

B:Maximum

Left

Right

Groove at the
Base A/C

Height Adjustment Screw(B)

Tilt Adjustment Screw(C)

Azimuth Adjustment
Screw(A)

X-Value Adjustment Hole

Fixed Screw

RF ENVELOPE OUTPUT TEST POINT

OSCILLOSCOPE

HEAD SWITCHING OUTPUT TEST POINT

Connection Diagram

Adjustment Diagram

NOTE:

CH-1 CH-2

«
...
50
51
52
53
54
...
»

Summary of Contents for VHR-H772EV




























































































Reviews:

No comments

Related manuals for VHR-H772EV

Brand: Fisher Pages: 40

Brand: JVC Pages: 81

Brand: JVC Pages: 76

OmniVision PV-QV201

Brand: Panasonic Pages: 28

OmniVision PV-QV200

Brand: Panasonic Pages: 36

Omnivision PV-S7680

Brand: Panasonic Pages: 44

Omnivision PV-S4680

Brand: Panasonic Pages: 40

Omnivision PV-S7670

Brand: Panasonic Pages: 44

OmniVision PV-Q920

Brand: Panasonic Pages: 40

Omnivision PV-S4690

Brand: Panasonic Pages: 48

Omnivision PV-9455S

Brand: Panasonic Pages: 40

Omnivision PV-9400

Brand: Panasonic Pages: 40

Omnivision PV-8450

Brand: Panasonic Pages: 36

Omnivision PV-8200

Brand: Panasonic Pages: 32

Omnivision PV-8661

Brand: Panasonic Pages: 40

Omnivision PV-HD1000

Brand: Panasonic Pages: 49

Omnivision PV-HD1000

Brand: Panasonic Pages: 49

Omnivision PV-8455S

Brand: Panasonic Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands