Sanyo VHR-H772EV Service Manual Download | Manualshive

Page: 49 / 91

background image

4-14

DECK MECHANISM ADJUSTMENT

Purpose: To insure smooth Transport of the Tape during each Mode of Operation.

If the Tape Transport is abnormal, then check the Torque as indicated by the chart below.

2. Preparation for Adjustment (To set the

Deck Mechanism to the Loading state
without inserting a Cassette Tape).

1) Unplug the Power Cord from the AC Outlet.
2) Disassemble the Top Cover and Plate Assembly Top.
3) Plug the Power Cord into the AC Outlet.
4) Turn the Power S/W on and push the Lever Stopper of

the Holder Assembly CST to the back for Loading the

Cassette without Tape.
Cover the Holes of the End Sensors at the both sides of
the Bracket Side(L) and Bracket Assembly Door to pre-
vent a light leak.
Then The Deck Mechanism drives to the Stop Mode.
In this case, The Deck Mechanism can accept inputs of
each mode, however the Rewind and Review Operation
can not be performed for more than a few seconds
because the Take-up Reel Table is in the Stop State
and can not be detected the Reel Pulses.

3. Checking Torque

The Values are measured by using a Torque Gauge and
Torque Gauge Adaptor with the Torque Gauge affixed.

The Torque reading to measure occurs when the Tape
abruptly changes direction from Fast Forward of Rewind
Mode, when quick bracking is applied to both Reels.

SRK

VIDEO

CASSETTE

TORQUE

METER

VHT-303

S

R

K

-

V

H T

- S

SR

K - V H T - T

300

250

200

150

50

0

300

250

200

150

50

0

100

Test Equipment/ Fixture

• Torque Gauge(600g/cm ATG)
• Torque Gauge Adaptor
• Cassette Torque Meter

SRK-VHT-303

Checking Method

• Perform each Deck Mechanism Mode without

inserting a Cassette Tape(Refer to above No.2
Preparation for Adjustment).

• Read the Measurement of the Take-up or Supply

Reels on the Cassette Torque Meter(Fig. C-3-2).

• Attach the Torque Gauge Adaptor to the Torque

Gauge and then read the Value of it(Fig. C-3-1).

NOTE:

Fig. C-3-2

Fig. C-3-1

Torque Gauge

Torque Gauge
Adaptor

Reel Table

Item

Fast Forward Torque

Rewind Torque

Play Take-Up Torque

Review Torque

Mode

Fast Forward

Rewind

Play

Review

Test Equipment

Cassette Torque Gauge

Cassette Torque Gauge

Cassette Torque Meter

Cassette Torque Meter

Measurement Reel

Take-Up Reel

Supply Reel

Take-Up Reel

Supply Reel

Measurement Values

More than 400g/cm

More than 400g/cm

40~100g/cm

120~210g/cm

Test Conditions

(Mechanism Condition)

• Play (FF) or Review (REW) Mode

NOTE:

• Cassette Torque Meter (SRK-VHT-303)

• Torque Gauge (600g.cm ATG)

«
...
47
48
49
50
51
...
»

Summary of Contents for VHR-H772EV




























































































Reviews:

No comments

Related manuals for VHR-H772EV

Brand: Magnavox Pages: 64

Brand: Palsonic Pages: 27

Brand: JVC Pages: 12

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 28

Brand: Philips Pages: 24

Brand: Philips Pages: 28

Brand: Philips Pages: 32

Brand: Philips Pages: 28

Brand: Philips Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands