Sanyo VCC-6974 Page 8 Instruction Manual Download | Manualshive

Page: 8 / 68

background image

CONCERNING AUTO-IRIS LENSES

DC type auto-iris lens

A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is
referred to as DC type coil lens or DC type non-amplifier lens.

(Set the

A.I. LENS

switch to the

DC

position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is
referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments.

(Set the

A.I. LENS

switch to the

VIDEO

position.)

Compatible auto-iris lenses

1/3 inch Sanyo DC type lens

VIDEO type lens

VCL-CS8LY: Standard angle, f= 8 mm

Standard angle, f= 9 mm

VCL-CS4LY: Wide angle, f= 4 mm

Telephoto angle, f= 12 mm

VCL-CS2LY: Ultra-wide angle, f= 2.8 mm

Greater telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

•

Set the

ALC

and

LEVEL

controls on the lens to adjust the iris. Normally the

ALC

volume should be turned

all the way to

Av

(Average).

•

Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the

LEVEL

volume on the lens casing to correct.

DC
VIDEO

A. I.

LENS

L53R4/US GB 1999, 12, 7

English

7

«
...
6
7
8
9
10
...
»

Summary of Contents for VCC-6974





































































Reviews:

No comments

Related manuals for VCC-6974

Brand: Samsung Pages: 114

Brand: Samsung Pages: 2

Brand: Samsung Pages: 136

Brand: Harbor Freight Tools Pages: 3

Brand: Yada Pages: 20

Brand: Ganz Thermal Pages: 2

Brand: Safety Vision Pages: 21

EXPCMR-ALG-OZ-IC-1080P-1224 HD-TVI

Brand: Larson Electronics Pages: 4

Brand: ViewSonic Pages: 2

Brand: FujiFilm Pages: 2

Brand: Axis Pages: 56

Brand: Geutebruck Pages: 2

Brand: TZT Pages: 12

Brand: Targa Pages: 386

Brand: MAGINON Pages: 64

E-410 - EVOLT Digital Camera SLR

Brand: Olympus Pages: 132

Brand: Olympus Pages: 79

Brand: Casio Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands