Sanyo VCC-6974 Page 13 Instruction Manual Download

Page: 13 / 68

CONNECTIONS

About the Alarm output terminal

Connect this unit to a VCR or a multiplexer.

Alarm output

: Alarm signal output

: Common

CAUTION:

•

The digital processing of the settings may disturb the image for
a few seconds after the camera is turned on.

•

While the menus are being set, noise sent on the lines by
peripheral devices may cause the settings to change. In such a
case, turn the power off then on again.

Remote controller circuit connections

Use the layout above to make a remote controller and make the
connections to the remote input pins (C, R) of the

REMOTE

terminal

as indicated. This will permit remote controlled operation of this unit.
(make contact LOW input)

Note:

•

The maximum length of cable for remote controlled operation is
6 m (AWG 24).

•

If the ZOOM item in the

OPTION MENU

is set to

, remote

controlled zoom is possible even while the menu screens are
displayed.

Alarm active

About 500 msec.

5 V

SW 1

SW 2

SW 3

SW 4

SW 5

SW 6

SW 7

SW 8

1.1k

Ω

0.68k

Ω

0.91k

Ω

1.2k

Ω

1.8k

Ω

2.7k

Ω

3.9k

Ω

9.1k

Ω

: Zoom (wide)

: Zoom (tele)

: Panning (left)

: Panning (right)

: Tilting (upward)

: Tilting (down)

SW: switch

: Electric PTZ
(pan-tilt-zoom) preset

: Electric PTZ
(pan-tilt-zoom) OFF

*Preset: will return to the zoom (pan,

tilt) center position.

L53R4/US GB 1999, 12, 7

English

Summary of Contents for VCC-6974





































































Search results

Summary of Contents for VCC-6974

Reviews:

Related manuals for VCC-6974

Brands by name

Popular brands

Sanyo VCC-6974, Instruction Manual

Search results

Summary of Contents for VCC-6974

Reviews:

Related manuals for VCC-6974

Brands by name

Popular brands