Santec ECL-210 Operation Manual Download Page 47

Page: 47 / 96

7-10

ECL-210 Operation Manual

LD.ON

APC.ON

COH.ON

STATUS

7.6. MLS Matrix LED

MLS provides matrix LED for monitoring the status of the all unit inserted. The vertical line

shows slot numbers and the horizontal line does the status of each unit.

The relation between the unit status of the horizontal line and LED is as follow.

MODE

Display,shuttle switch

Unit

ON/OFF key

Current

Current ON/OFF

APC

OpticalPower

dBm

APC/ACC Switching

COH

OpticalPower

dBm

COH ON/OFF

CURR

Current

N/A (Non Applicable)

TEMP

LD Temperature

ºC

N/A

POWER

Optical Power

dBm

N/A

WAVE

Wavelength

N/A

FINE

Fine Tuning

N/A

Silk

The Condition of Lighting

LD.ON

Current is injected into LD.

APC.ON

The status isAPC.

COH.ON

COH is ON.

STATUS

It indicates the plural operations state. It shows
OR of the tuning wavelength, changing current,
unstable temperature, and controlling ATT.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for ECL-210

































































































Search results

Summary of Contents for ECL-210

Reviews:

Related manuals for ECL-210

Brands by name

Popular brands

Santec ECL-210, Operation Manual

Search results

Summary of Contents for ECL-210

Reviews:

Related manuals for ECL-210

Brands by name

Popular brands