manualshive.com logo in svg

SANDVIK CH420:01, Installation Manual

Share
Download
SANDVIK CH420:01 Installation Manual Download Page 46

4. Installation preparations

44

© Sandvik SRP AB – Doc. no. S 223.510 en Ver. 1

  

CH420:01

4.3 Installation preparations check list

Comments to the installation preparations check list are found in the 
following pages.

System

Checks

Remarks

Date/sign

Placement

Site access checked for cone crusher 
dimensions?

Smallest area that the cone crusher 
components must pass through? 
(W × H)

× 

Available service area?
(L × W × H)

× × 

Available lifting device on site?

Type:

Length of oil hoses and pipes?

Length of drive belts?

Foundation

Foundation constructed according to 
drawings?

Electrical system

All necessary cables to the cone 
crusher arranged?

Length of cables?

All necessary switchgear installed?

All necessary connections to plant 
control system arranged?

Electrical power available?

Process material

Process material tested by Sandvik?

Dust protection

Dust protection complies with local 
regulations?

Feed arrange-
ment

Feed arrangement designed 
correctly?

Discharge

Discharge arrangement ready to be 
connected to outlet of crusher?

Guards

Need for additional guards?

Platforms and 
guard rails

Comply with local regulations? 
Designed so they do not interfere with 
the cone crusher’s function?

Summary of Contents for CH420:01















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands