manualshive.com logo in svg

S&C 6800 Series, Navigation Manual, Page: 13 / 17

Share
Download
S&C 6800 Series Navigation Manual Download Page 13

Switch Control Configuration

The 

Site-Related

 tab configures settings for the specific control site. See Figure 9.

Make sure the 

Line kV to 120 Vac Base Ratio

 setpoint is correct. This is the voltage 

step-down ratio of all customer-load transformers on the feeder. The control records, 
displays, and manipulates voltages normalized on a 120-Volt or 240-Volt base. This  
setting is the conversion ratio from line voltage to base voltage. The 

Voltage  

Transformer Wiring

 setting configures the switch control for customer voltage 

reporting. The control uses this information when calculating kvars. Set as either  

Phase-to-Neutral

 or 

Phase-to-Phase

 mode.

At the bottom of the screen are the 

Installation Voltage-Current Phase Angle  

Offset

 settings. The setpoints (one for each voltage-current phase) allow installation-

dependent phase-angle corrections. The angle offsets are used to determine the Normal 
Current and Reverse Current flow direction.

Site-Related Settings

Figure 9. The Setup>General>Site-Related screen.

The 

Metering

 screen reports the current and voltage passing through each phase.  

This is real-time data. See Figure 10.

Metering

Figure 10. The Metering screen for a 6802 switch control.

S&C Instruction Sheet 1045-511    13

Summary of Contents for 6800 Series


















Reviews:

No comments