manualshive.com logo in svg

Samsung VC-RA84V Series, Operation Manual

Share
Download
Samsung VC-RA84V Series Operation Manual Download Page 17

Emergency switch ON/OFF

In order to use the robot vacuum cleaner, the emergency switch 
located underneath of the main frame shall be turned on.

16

Installation of i-keeper

The cleaning zone of the robotic vacuum cleaner can be 
restricted with the fence (virtual wall) mode or several spaces 
can be cleaned with gate keeper (virtual door) mode. 

6

22

16

Installing the entry prevention tape               

(Exclusive use for VC-RA84V*SERIES) 

Always attach entry prevention tape to no entry 
area of robot vacuum cleaner.

21

5

■ 

Installation sequence

1

  ■ 

Emergency switch ON/OFF

1

If robotic vacuum cleaner is to be activated, emergency switch 
shall be turned on. If the emergency switch is turned off, all the 
settings will be initialized. When the emergency switch is turned 
off, all of the settings except current time will be initialized.

Turn on emergency switch by turning the main 

frame upside down.

▶ 

 If the icon is not turned on, the battery is in the state of 
no storage, therefore, turn on emergency switch, and 
perform charging to the charger.

▶ 

 As the setup time may differ with the current time, match 
it to the current time.

  

  ※   If there is no manipulation of user for about 10 minutes under the 

turned on state of power supply, power will automatically be turned 
off to save battery discharge. When using the device again, turn 
on the power with the power supply (activation/stop) button.

When emergency switch is turned off, charging will not taken 
place even if put (the robotic vacuum cleaner) on the charger.

20

Installing the charger

In order to have charging, install the charger in the first place.
When purchasing the product, the battery is in the discharged state, therefore,
use the charger after completely charging the battery.

2

17

Charging

In order to use robot vacuum cleaner, the battery shall be 
charged in advance.

3

18

Setting of time

In order to have daily reservation and                            
reserved cleaning, set up current time.

4

20

Installation of r

obotic vacuum 

cleaner

installation

Perform the installation in accordance with the following 
sequence.

Confirm at the time of 

installation.

DJ68-00517A-고급형(EN).indd   16

2010.5.6   1:32:32 PM

Summary of Contents for VC-RA84V Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands