Samsung VC-RA84V Series Operation Manual Download Page 11

Page: 11 / 48

회회회 회회

추락방지 센서

장애물 센서

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

측면

회전솔

파워브러시

ecautions for safety

preparation

These are the contents to secure the safety of user and to prevent damage of property.
Please have safe operation by reading carefully of the following items.

Always observe followings for

safety

Handling after the use

During the handling, do

not directly spray water

or polish the outside with

volatile substances such

as benzene, thinner,

and alcohol etc.

▶

Fatal damage can be

inflicted on the product.

Regularly wipe off foreign
material accumulated on
the obstacle sensor and
falling prevention sensor.

▶

The sensors may have

malfunction due to the
covering with foreign
material.

When removing foreign
material, always turn off
the emergency switch in
the first place, and then,
use the brush for
cleaning.

▶

If suddenly activated,

injury or fatal damage
to the product can be
brought.

Do not squeeze with

force or strongly press

the bumper

▶

If bumper sensor

becomes abnormal,

collision with the

surface of wall or

fixture and so forth

can be happened.

Never disassemble or

modify the robotic

vacuum cleaner except

qualified repair

technician.

▶

Fatal damage to the

product can be

happened.

In the case of damaging

power supply cord,

exchange it through the

qualified repair

technician of customer

care center.

▶

There is the danger of

electric shock or fire.

Do not handle the
charger before
separating the power
supply plug.

When exchanging
battery, call up the
customer care center of
Samsung Electronics.

▶

If using battery which is

not a legitimate
product, it will be the
cause of failure.

DJ68-00517A-고급형(EN).indd 10

2010.5.6 1:32:17 PM

Summary of Contents for VC-RA84V Series

















































Search results

Summary of Contents for VC-RA84V Series

Reviews:

Brands by name

Popular brands

Samsung VC-RA84V Series, Operation Manual

Search results

Summary of Contents for VC-RA84V Series

Reviews:

Brands by name

Popular brands