manualshive.com logo in svg

Samsung SN6000 Series, User Manual

Share
Download
Samsung SN6000 Series User Manual Download Page 53

Samsung SN6000 Series User’s Manual

Using the Battery 42

Figure 20. Battery Gauge

The gauge has two sections:

The top section of the gauge shows a picture of a battery to
indicate that the computer is operating from the battery.

The bottom section of the gauge shows you the amount of
battery charge remaining.

While the battery gauge is displayed, all keys are disabled. The battery
gauge closes in a few seconds.

Using PowerProfiler to Monitor the Battery

PowerProfiler enables you to set power-management options for
computers shipped with Windows NT installed. To use PowerProfiler
to monitor the battery charge, place the cursor on the battery icon in the
right corner of the taskbar. PowerProfiler shows you the amount of
battery charge remaining.

The color of the battery icon also indicates approximate battery charge:

Green: Charge is adequate to power computer.

Yellow: Charge is low.

Red: Charge is very low.

You can determine at what battery charge level PowerProfiler shows
the low and very low colors. The default setting for the very low level
is 20 percent battery charge remaining.

To set battery monitoring options in PowerProfiler:

Summary of Contents for SN6000 Series

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands