manualshive.com logo in svg

Samsung SN6000 Series, User Manual

Share
Download
Samsung SN6000 Series User Manual Download Page 101

Samsung SN6000 Series User’s Manual

Troubleshooting 90

the Installed O/S field in System Setup is set to other. Check to
make sure that the port is enabled in System Setup.

A PC Card does not work correctly.

Make sure that the PC Card is inserted right side up in the PC Card
slot. Check that the card is inserted fully into the slot. If you are
using a PC Card modem, check the modem cable connections. If
you are using an operating system that is not plug and play
compliant, make sure the Installed O/S field in System Setup is set
to Other.

The System Setup settings are not retained when you turn off the
computer.

The CMOS battery inside the computer may need to be replaced.
The CMOS battery provides power to save the system BIOS
information when the computer is turned off. Normally, the
CMOS battery lasts for several years. Do not attempt to open the
chassis and replace this battery yourself or your warranty is void.
Have an authorized Samsung service center replace the CMOS
battery.

Summary of Contents for SN6000 Series

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands