Samsung SHR-5042 User Manual Download Page 19

Page: 19 / 78

TIN

connecting with other devices _

CONNECTING THE RS-485 DEVICE

Caution



Please check that the RS-485 device is supported by the SHR-5040/5042 product. And, a caution shall be

made when connecting to the RS-485 jack since it has the polarity (+ and –).

CONNECTING THE USB

It has a total of 2 USB connection ports on the front and rear sides of SHR-5040/5042.

Connect the USB HDD, USB memory through the front/rear ports of SHR-5040/5042.

Only one USB device can be connected to each USB port.

It provides the hot-plugging function that allows connecting/disconnecting a USB device while operating the system.

Caution



You can connect the same type of USB devices to the USB ports on the front and rear sides of

SHR-5040/5042.

Port for connecting the RS-485 signal wire

(connect to the RX-Receiver)

SHR-5042_Eng.indb 15

2007-06-08 ｿﾀﾈﾄ 1:24:30

Summary of Contents for SHR-5042















































































Search results

Summary of Contents for SHR-5042

Reviews:

Related manuals for SHR-5042

Brands by name

Popular brands

Samsung SHR-5042, User Manual

Search results

Summary of Contents for SHR-5042

Reviews:

Related manuals for SHR-5042

Brands by name

Popular brands