Samsung S3F84B8 User Manual Download Page 215 | Manualshive

Page: 215 / 322

background image

S3F84B8_UM_REV 1.00

8 RESET AND POWER-DOWN

8-5

8.2.1.3 Idle Mode

Idle mode is invoked by the IDLE (opcode 6FH) instruction. In Idle mode, the CPU operations are halted while
select peripherals remain active. During Idle mode, the internal clock signal is gated off to the CPU, but not to the
interrupt logic and timer/counters. Port pins retain the mode (input or output) they had at the time of entering Idle
mode.

There are two ways to release the Idle mode:

1. Execute a Reset: All system and peripheral control registers are reset to their default values and the contents

of all data registers are retained. The Reset automatically selects a slow clock (f

xx

/16) because CLKCON.3

and CLKCON.4 are cleared to “00B”. If interrupts are masked, Reset is the only way to release Idle mode.

2.  Activate any enabled interrupt, causing Idle mode to be released: When you use an interrupt to release Idle
    mode, the CLKCON.3 and CLKCON.4 register values remain unchanged and the selected clock value is
    used. The interrupt is then serviced. The interrupt service routine will then return to the instruction immediately
    following the STOP instruction.

NOTE:

Only external interrupts that are not related to clock can be used to release the Stop mode. To release the Idle mode,

any type of interrupt (that is, internal or external) can be used.

Before entering the STOP or IDLE mode, ADC must be disabled. Otherwise, the STOP or IDLE current will increase

significantly.

«
...
213
214
215
216
217
...
»

Summary of Contents for S3F84B8



































































































































































































































































































































Reviews:

No comments

Related manuals for S3F84B8

Brand: OBH Nordica Pages: 16

Brand: Raco Pages: 3

Brand: Sunbeam Pages: 16

Marble + Brass 2743412

Brand: West Elm Pages: 3

Brand: Funtime Pages: 10

Brand: Faber Pages: 10

Brand: Omcan Pages: 8

Brand: Astivita Pages: 13

Brand: Zeegma Pages: 56

Brand: Parkinson Cowan Pages: 48

Brand: AGA Pages: 40

Brand: Omcan Pages: 16

Lucky Lifestyle LA BELLE SHSSAL6A

Brand: creative housewares Pages: 4

Brand: ChefMaster Pages: 5

SOUS VIDE SVS-1200S

Brand: Wilfa Pages: 148

Brand: Fhiaba Pages: 72

Brand: Korona Pages: 28

Brand: Krups Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands