background image

80  Users Manual

Tips for Using Your Computer

The following information helps you avoid potential problems as you use your 
computer:

Do not try to disassemble your computer. Opening the system chassis or 
removing the hard disk drive voids your warranty. Only an authorised 
Samsung service center can replace or add any parts inside the chassis.

Follow all the instructions and cautions in your computer user documentation.

The LCD has a polarized surface and can be damaged easily. To prevent 
damage, avoid touching the screen.

Use only approved AC adapters, auto adapters, memory modules and other 
options.

Because a notebook computer is small and has restricted air flow around 
components, it is more likely to overheat than a desktop computer. A fan inside 
your computer runs when needed to help eliminate heat. Make sure the fan vent 
on the left side of your computer is not blocked when you use the computer. 
Occasionally check the vents and remove any accumulated dust on the outside. 

Avoid using or storing the computer in extremely hot or cold areas, such as a 
car on a hot day. Keep the computer away from heaters and out of direct 
sunlight. Exposure to excessive heat may damage computer components. If you 
have left your computer in a hot place, let it cool down slowly to room 
temperature (with the LCD panel open) before using it.

Do not remove the memory-module compartment door, or try to install a 
memory module when the computer is on.

Set up your computer work area to avoid physical strain. Sit with your back 
straight and supported by your chair. Adjust your chair or work table so that 
your arms and wrists can remain in a relaxed position, parallel with the floor. 
Avoid bending or twisting your wrists as you work. Your hands should “float” 
slightly above the keyboard. Refer to a book on office ergonomics for more 
information on setting up your work area.

Take frequent breaks from working at the computer to rest your eyes and 
stretch your muscles. 

Remember to save your data files frequently and to make backup copies of your 
files.

Summary of Contents for NX15


































































































































































































































































Reviews: