Samsung NX15 User Manual Download Page 37 | Manualshive

Page: 37 / 257

background image

24 Users Manual

If you remove the CD when the CD access LED is on, the disk and the data in
it may be damaged.

Emergency Eject Hole

To eject a CD when the CD drive is not working or the computer is turned off,
unfold a paperclip, and insert the unfolded end of the clip into the emergency
eject hole (located next to the eject button) and press until the CD tray opens.

To clean a CD or DVD title

Clean the disc with a soft clean cloth by wiping from the center outwards.

To play a DVD

You have to install the DVD software provided on a separate CD to view a
DVD title.

To use the Windows Media Player

The Windows Media Player allows you to play audio and video files from the computer
or the Internet.

To launch the Windows Media Player, click

Start > All Programs > Accessories >

Entertainment > Windows Media Player

.

Features

Playback Control Area

Playlist

«
...
35
36
37
38
39
...
»

Summary of Contents for NX15


































































































































































































































































Reviews:

No comments

Related manuals for NX15

Brand: Gateway Pages: 16

Toughbook CF-Y5LWEZABM

Brand: Panasonic Pages: 40

VisionBook N15R Pro

Brand: UMAX Technologies Pages: 82

Brand: Ace Pages: 282

TravelMate 4070

Brand: Acer Pages: 80

TravelMate 4070

Brand: Acer Pages: 77

TravelMate 4070

Brand: Acer Pages: 79

TravelMate 4060

Brand: Acer Pages: 68

Aspire Lite AL15-51

Brand: Acer Pages: 22

Brand: Acer Pages: 14

Aspire Switch 10

Brand: Acer Pages: 76

Brand: Acer Pages: 33

Brand: Acer Pages: 108

Brand: Acer Pages: 85

Aspire 9420/ 9410/ 7110 TravelMate 5620/ 5610/...

Brand: Acer Pages: 116

Brand: Acer Pages: 210

Aspire 7520 Series

Brand: Acer Pages: 106

Brand: Acer Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands