manualshive.com logo in svg

Samsung NX15, User Manual

The Samsung NX15 is a remarkable digital camera equipped with advanced features and superior image quality. Capture breathtaking shots effortlessly with this sleek device. For your convenience, a comprehensive User Manual is available for download, absolutely free, from manualshive.com. Discover the full potential of your Samsung NX15 through this comprehensive manual.

Share
Download
background image

7-12

Manual

Q13 When the computer enters standby mode or hibernate mode,

screen of a connected TV is broken for a short time.

A This problem may occur in some wide screen TVs. After a short time, the TV turns

off properly.

Q14 When I restarted the computer from hibernate mode, the

screen is not displayed properly.

A This problem may occur when the TV is set to primary display device, and the

CRT to secondary. Change the display device differently. (Refer to ‘Using External
Display Devices (P. 6-8)’)

Q15 When I connected and used a projector, the screen is broken for a

short time.

A When you use DOS mode with some projectors, this problem may occur while

changing the video mode. The screen is displayed properly after a short time.

Q16 When I set the extended desktop to display through both LCD

and TV and restarted the computer, the setting is changed to
dual display mode.

A Set to extended desktop again on [Graphics Controller Properties] dialog. (Refer

to ‘Using External Display Devices (P. 6-8)’)

Q17 When I changed the screen resolution in extended screen mode

and restarted the computer, the screen is not displayed properly.

A This problem may occur when the display is set to ‘Restart the computer before

applying the new display settings’. (Start > Control Panel > Appearance and
Themes > Display > Settings tab > Advanced > General tab)
1. Click Start > Control Panel > Appearance and Themes > Display > Settings

tab > Advanced > General tab. Select ‘Apply the new display setting without
restarting’ and click OK.

2. Change the screen resolution on [Graphics Controller Properties] dialog, and

apply immediately without restarting the computer. (Refer to ‘Using External
Display Devices (P. 6-8)’)

Q18 When I pressed <Fn>+<F4 / LCD/CRT> keys, the screen res-

olution is changed.

A  This problem may occur when the screen resolution of CRT mode is different

from that of LCD or LCD/CRT mode. Configure the CRT mode screen resolution
same as the LCD mode screen resolution.

Summary of Contents for NX15


































































































































































































































































Reviews:

No comments

Related manuals for NX15

Samsung NP680Z5E Guías Del Usuario Manual preview
NP680Z5E
Brand: Samsung Pages: 155
Samsung NP520U4C User Manual preview
NP520U4C
Brand: Samsung Pages: 154
Samsung NP270E5E Guías Del Usuario Manual preview
NP270E5E
Brand: Samsung Pages: 143
Samsung NP-X22 Guía Del Usuario preview
NP-X22
Brand: Samsung Pages: 186
Samsung Galaxy Book S Quick Reference Manual preview
Galaxy Book S
Brand: Samsung Pages: 2
Samsung Chromebook Troubleshooting Manual preview
Chromebook
Brand: Samsung Pages: 13
Gateway Notebook User Manual & Code Book preview
Notebook
Brand: Gateway Pages: 128
Gateway Notebook Setup Manual preview
Notebook
Brand: Gateway Pages: 2
eMachines E732 Service Manual preview
E732
Brand: eMachines Pages: 192
IBM Intel PRO/100 SP User Manual preview
Intel PRO/100 SP
Brand: IBM Pages: 72
Dell Adamo XPS Service Manual preview
Adamo XPS
Brand: Dell Pages: 59
Dell A13-USE002AM - Adamo - Laptop System And Support Information preview
A13-USE002AM - Adamo - Laptop
Brand: Dell Pages: 58
Dell 8KPKX Setup preview
8KPKX
Brand: Dell Pages: 21
Dell Latitude 7285 Owner'S Manual preview
Latitude 7285
Brand: Dell Pages: 71
Toshiba A105-S2121 Specifications preview
A105-S2121
Brand: Toshiba Pages: 10
Toshiba A105-S2101 Specifications preview
A105-S2101
Brand: Toshiba Pages: 10
Toshiba M750-S7213 Specifications preview
M750-S7213
Brand: Toshiba Pages: 5
Toshiba M65-S9093 Specifications preview
M65-S9093
Brand: Toshiba Pages: 4

Brands by name

Popular brands

Load more brands