Samsung NX15 User Manual Download Page 128 | Manualshive

Page: 128 / 257

background image

Specifications 115

Wireless LAN Specification (Optional)

Intel(R) PRO/Wireless LAN 2100 3B Mini PCI Adapter

Product Specification

* This piece of equipment supports the Wi-Fi wireless LAN security standard, WPA (Wi-Fi Protected Access) and
CCX (Cisco Compatible eXtensions). To connect to a wireless network consisting of the WPA and CCX, 1.2.2.8
or higher version of wireless LAN driver have to be installed on your computer, and certificates, Windows patch
(KB826942) or PROSet may be required depending on the network settings. For driver update, visit
www.samsung.com and for information on the PROSet installation, refer to ”Wireless Network Setup Using the
Wireless LAN Setup Program” (p 51). For more information, ask your network administrator.

Radio Specifications

* The transmission rate may differ from the actual transmission rate.

Item

Detailed Specifications

Physical
Specifications

Dimensions

(Width X Height) 59.75 X 44.45 mm

operation temperature and
humidity

Same as system operation

Temperature: 0°C ~ 70°C
Humidity: less than 85%

Power Specification

Power Saving Mode

135 mW

Receiving Mode

1.0 W

Transmission Mode

1.6 W

Power

3.3V

Network
Specifications

Compatibility

IEEE802.11b

Operating System

Microsoft Windows XP, 2000
- NDIS5 Miniport Driver

Media Access Protocol

CSMA/CA (Collision Avoidance) with
Acknowledgement(ACK)

Security

Wired Equivalent Privacy support (WEP)
64bit / 128bit

RF Band

2.4GHz (ISM band)

Support Channels

1~13 channel (See "Regulatory Notice for Channel Use in France".)

Device

Transceiver

Standard Output Power

5 mW

Transmission Method

DSSS

Transmission Rate (Mbps) *

11, 5.5, 2, and 1

Antenna Type

Internal Antenna 2 EA (Main/Aux)

«
...
126
127
128
129
130
...
»

Summary of Contents for NX15


































































































































































































































































Reviews:

No comments

Related manuals for NX15

Brand: Gateway Pages: 52

6200-A DeskNote

Brand: EUROCOM Pages: 67

Chromebook CB315-3H

Brand: Acer Pages: 33

Chromebook CB5-132T

Brand: Acer Pages: 36

Brand: Acer Pages: 32

P3010 - LifeBook - Athlon Neo 1.6 MHz

Brand: Fujitsu Pages: 13

P8020 - LifeBook - Core 2 Duo 1.4 GHz

Brand: Fujitsu Pages: 2

T2020 - LifeBook Tablet PC

Brand: Fujitsu Pages: 210

S6510 - LifeBook - Core 2 Duo GHz

Brand: Fujitsu Pages: 203

P8020 - LifeBook - Core 2 Duo 1.4 GHz

Brand: Fujitsu Pages: 189

6535b - Compaq Business Notebook

Brand: HP Pages: 38

Brand: Hama Pages: 22

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VGNZ790DIB - VAIO Z Series

Brand: Sony Pages: 2

VGNZ790DJB - VAIO Z Series

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands