Samsung DMT400 series Service Manual Download Page 18 | Manualshive

Page: 18 / 58

background image

3-8

3. Disassembly and Reassembly

Part

Photo

Description

Condensing dry

system

Assy Case Vent

&

Assy Dry Duct

&

Assy Duct

Condenser

5. Remove the Assy case vent by rotating it

counterclockwise.

6. Remove the Assy dry duct from the Assy duct

condenser.

These parts are

fi

xing by four(4) hooks. To

disassemble, hooks are broke down in the Assy dry
duct.

Caution

Only when dry motor is not working, disassemble it.
After remove it, you should use new Assy dry duct
part to reassemble.

7. Pull out Assy dry duct.

Assy Case Vent

1. Remove the Assy case vent.

2. Release two screws.

3. Pull the thermal actuator

fi

rmly to remove it from the

housing and to release it from the gasket vent.

坍

Reassembly is in the reverse order of the removal.

«
...
16
17
18
19
20
...
»

Summary of Contents for DMT400 series



























































Reviews:

No comments

Related manuals for DMT400 series

Brand: Malber Pages: 16

Brand: Samsung Pages: 68

WW7 J5 6 Series

Brand: Samsung Pages: 48

Brand: Samsung Pages: 118

Brand: Samsung Pages: 6

Brand: Samsung Pages: 44

Brand: Samsung Pages: 10

Brand: Samsung Pages: 80

Brand: Samsung Pages: 22

Brand: Samsung Pages: 264

Brand: Samsung Pages: 40

Brand: Samsung Pages: 40

Brand: ZEP Pages: 36

Brand: NEFF Pages: 26

Brand: V-ZUG Pages: 76

Brand: Furrion Pages: 26

T-1200 WC1200XA-12

Brand: Dexter Laundry Pages: 25

Brand: Heinner Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands