Samsung DMT400 series Service Manual Download Page 47

Page: 47 / 58

4. Troubleshooting

4-14

Error type

Error mode

Checking Method

Corrective actions

The nozzle does not
inject water

None

1. Check the connections for the Circulation Motor

connector.

- Reconnect the Circulation Motor connector.

2. Check the connections for the Startup Condenser

connector of the Circulation Motor.

- Reconnect the Startup Condenser connector of the Circulation Motor.

3. Check the resistance for the Circulation Motor coil.

(Remove the connector before measuring.)

- Between black wire and white wire

Normal: Approx. 15

- Between black wire and blue wire

Normal: Approx. 21

- Faulty: Replace the Circulation Motor.

4. Check the operation of the Circulation Motor Relay.

- At No.2 mode in service inspection mode,
Check the operating voltage between the

yellow wire of the CN101 connector and the
white wire of the CN201 connector.
Normal: 120V (while operating)

- At No.3 mode in service inspection mode,

Check the operating voltage between the
yellow wire of the CN101 connector and the
blue wire of the CN201 connector.
Normal: 120V (while operating)

- Faulty: Replace the Main PBA assy.
- Normal: Replace the Circulation Motor.
- Remove

retainer.

- Check voltage while operating Wash motor-2(High)

- Check voltage while operating Wash motor-1(Low)

5. Check whether there is foreign material in the water

passages.

- Remove foreign material from the water passages.

Summary of Contents for DMT400 series



























































Search results

Summary of Contents for DMT400 series

Reviews:

Related manuals for DMT400 series

Brands by name

Popular brands

Samsung DMT400 series, Service Manual

Search results

Summary of Contents for DMT400 series

Reviews:

Related manuals for DMT400 series

Brands by name

Popular brands