Samsung DMT400 series Service Manual Download Page 24

Page: 24 / 58

3-14

3. Disassembly and Reassembly

Part

Photo

Description

Shutter

Leakage Sensor

Preparation:

* Make sure to disconnect the power & water supply

& drain hose connections.

* Remove the upper & lower baskets in the

dishwasher.

* Pull out the dishwasher carefully.

1. Lay down the dishwasher on its back. Release the

two(2) screws

xing the base and shutter in place.

2. Pull out the shutter and release the leakage sensor

connector.

3. Remove the leakage sensor from the shutter by

unfastening the two(2) screws.

Rear Leg

Case gear

Adjust leg bar

Preparation:

* Make sure to disconnect the power & water supply

& drain hose connections.

* Remove the upper & lower baskets in the

dishwasher.

* Pull out the dishwasher & Lay down the dishwasher

on its back carefully.

* Remove the shutter.

1. Rotate the rear leg adjust bar below Door to right

turn entirely until pull out the rear leg.

2. Release the screw that is holding case gear and

remove it.

3. Case gear is made up of worm gear and helical

gear. Pull out worm gear at

rst.

4. Hold the adjust bar & pull in it pushing helical gear

from backside.

Adjust leg bar is holding by hook which is inside red
circle.

坍

Reassembly is in the reverse order of the removal.

Summary of Contents for DMT400 series



























































Search results

Summary of Contents for DMT400 series

Reviews:

Related manuals for DMT400 series

Brands by name

Popular brands

Samsung DMT400 series, Service Manual

Search results

Summary of Contents for DMT400 series

Reviews:

Related manuals for DMT400 series

Brands by name

Popular brands