Samsung DMT400 series Service Manual Download Page 13 | Manualshive

Page: 13 / 58

background image

3-3

3. Disassembly and Reassembly

Part

Photo

Description

Main PBA

Preparation:

* Make sure to disconnect the power.

1. You can see the Main-PBA case under the door.

2. Remove the two (2) screws of PBA case and pull

out the PBA cover carefully.

3. Remove the all connectors in the PBA include

two(2) fasten type ones at right side.

4. Remove the three (3) screws on the PBA board.

5. Pull out the PBA board carefully..

When removing the Main PBA, lift up the PBA board
carefully because it is hanging to the PBA case with
two(2) hooks.

If you feel hard to disconnect the wire connectors.
Follow the below.

a. Release two(2) fasten type connector located right

side.

b. Unscrew the three(3) screws in PBA board & pull

out the PBA board.

c. Disconnect the wire connectors.

坍

Reassembly is in the reverse order of the removal.

«
...
11
12
13
14
15
...
»

Summary of Contents for DMT400 series



























































Reviews:

No comments

Related manuals for DMT400 series

Brand: Hotpoint Ariston Pages: 24

Brand: Daewoo Pages: 33

Brand: Baumatic Pages: 28

Brand: SCHOLTES Pages: 52

Brand: Parmco Pages: 49

Brand: AEG Electrolux Pages: 108

Brand: Indesit Pages: 16

Brand: Smeg Pages: 27

MDC4650AWB - Jet Clean II 24" Portable Dishwasher

Brand: Maytag Pages: 2

Brand: Gorenje Plus Pages: 200

Brand: Asko Pages: 28

Brand: Hanseatic Pages: 84

GU2275XTVY - 24" Wide Energy ST

Brand: Whirlpool Pages: 2

Brand: Electrolux Pages: 30

Brand: Electrolux Pages: 44

EIFLS20QS Series

Brand: Electrolux Pages: 28

CALIMA EWFM 14480 W

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands