Samsung Electronics
4-30
Installation
2. Must use insulator which is thick enough to
cover more than 10mm the refrigerant tube to
protect the condensate water on the outside of
pipe falling onto the floor and the efficiency of
the unit will be better.
3. Cut off any excess foam insulation.
4. Be sure that there must be no crack or wave on
the bended area.
5. It would be necessary to double the insulation
thickness to prevent condensation even on the
insulator when if the installed area is warm and
humid.
6. Shape an oil trap as shown in figure. The oil
trap must be formed every level difference of
6m.
7. For further details on connecting up to the
outdoor unit and purging the refrigerant circuit.
NOTE
:
◆
For further details on connecting up to the
outdoor unit and purging the refrigerant circuit.
4-5-8 Cutting/Flaring the Pipes
Connect the pipe within 30m and cutting pieces will not
be gone into the pipe as being clean to pipe section
1. Make sure that you have the required tools
available (pipe cutter, reamer, flaring tool and pipe
holder).
2. If you wish to shorten the pipes, cut it with a
pipe cutter, taking care to ensure that the cut
edge remains at a 90° angle with the side of the
pipe. Refer to the illustrations below for
examples of edges cut correctly and incorrectly.
3. To prevent any gas from leaking out, remove all
burrs at the cut edge of the pipe, using a reamer.
Radius
5cm
Oil trap
(suction tube)
Outdoor unit
Indoor unit
Oil trap
(Must be installed every 6m)
Oil trap
(Must be installed every 6m)
Outdoor unit
Indoor unit
a. When the indoor unit is above the outdoor unit
b. When the outdoor unit is above the indoor unit
90
O
Oblique
Rough
Burr
00152-OIAIN-5 2/1/01 1:56 PM Page 4-30
Summary of Contents for ACH1800E
