Samsung ACH1800E Service Manual Download Page 30

Page: 30 / 150

4-11

BUTTON NAME

ALL1

ALL0

"01" ~ "16"

FUNCTION

• To put on all 16 chambers' set.

• To put off all 16 chambers' set.

• To put on/off set assigned with the number.

• Since the centralized controller has the relay

equipment, the option mounted on the indoor
unit, the On/Off can be set for 16 chambers
through the modem communication.

• Linkage of wired remote controller to wired

remote controller is available by 3 kinds of level.

• The maximum extended distance of 1 Km is

possible through modem communication. (the
relay equipment is installed at the option item,
indoor unit)

• The connection by non-polarity method is easy.

Operating lamp

All On button

All Off button

On/Off indicators

On/Off buttons

Index

The centralized controller is an optional accessory.

NOTE : Operating lamp comes on when at least one air conditioner

connected to the centralized controller is operating.

4-3 Controller

4-3-1 Appearance and characteristics of Centralized Controller

The centralized controller is installed on the wall.

Samsung Electronics

00152-OIAIN-5 2/1/01 1:56 PM Page 4-11

Summary of Contents for ACH1800E























































































































































Search results

Summary of Contents for ACH1800E

Reviews:

Related manuals for ACH1800E

Brands by name

Popular brands

Samsung ACH1800E, Service Manual

Search results

Summary of Contents for ACH1800E

Reviews:

Related manuals for ACH1800E

Brands by name

Popular brands