Samsung ACH1800E Service Manual Download Page 13

Page: 13 / 150

3-2

Samsung Electronics

3-2 Name & Functions in Remote Control

Each time you press this button,
FAN SPEED is changed in the following order.

When the

indicator appeard on the remocon screen, cleaning the air

conditioner filter. After that, press this button.

FILTER SIGN

The ON Timer enables you to

switch on

the air conditioner automatically

after a given period of time that is from 30 minutes to 24 hours.
To cancel the On Time, press the (Set/Cancel) button.

The Off Timer enables you to

switch off

the air conditioner automatically

after a given period of time that is from 30 minutes to 24 hours.
To cancel the On Time, press the (Set/Cancel) button.

Each time you press this button
Mode is changed in the following order

Temp. down button. To decrease the temperature by the pressing
the temperature button

Temp. up button. To increase the temperature by the pressing
the temperature button

FUNCTION OF KEY

: Auto Mode

: Blowing

: Cooling Mode

: Heat Mode

: Dehumidifying Mode

(DOWN)

Power On/Off button to start and stop airconditioner or timer set up

To complete the installation, checks and tests to ensure that the air conditioner is
operating correctly.

NAMED OF KEY

(UP)

Adjust air flow vertically.

3-2-1 Wired Remote Controller-Buttons

00152-OIAIN-5 2/1/01 1:55 PM Page 3-2

Summary of Contents for ACH1800E























































































































































Search results

Summary of Contents for ACH1800E

Reviews:

Related manuals for ACH1800E

Brands by name

Popular brands

Samsung ACH1800E, Service Manual

Search results

Summary of Contents for ACH1800E

Reviews:

Related manuals for ACH1800E

Brands by name

Popular brands