Samsung ACH1800E Service Manual Download Page 51 | Manualshive

Page: 51 / 150

background image

Samsung Electronics

4-32

Installation

4-5-10 Fixing the Unit in Position

The outdoor unit must be installed on a rigid and stable
base to avoid any increase in the noise level and
vibration, particularly if the outdoor unit is to be
installed close to a neighbour. If it is to be installed in a
location exposed to strong winds or at a height, the unit
must be fixed to an appropriate support (wall or ground).

1. Position the outdoor unit so that the air flow is

directed towards the outside.

2. Attach the outdoor unit to the appropriate

support using anchor bolts.

3. If the outdoor unit is exposed to strong winds,

install shield plates around the outdoor unit, so
that the fan can operate correctly.

Capacity

A

B

UBH1800E, CH18ZAX, CH18CAX

582mm

340mm

UBH2400E, CH24ZAX, CH24CAX

660mm

340mm

UCH3600G, UCH4400G

CH36ZAX, CH44ZAX

840mm

415mm

CH36CAX, CH44CAX

A

B

00152-OIAIN-5 2/1/01 1:56 PM Page 4-32

«
...
49
50
51
52
53
...
»

Summary of Contents for ACH1800E























































































































































Reviews:

No comments

Related manuals for ACH1800E

Brand: BAC Pages: 30

Brand: inventum Pages: 100

Air Boss T1001 Module

Brand: Trion Pages: 23

Brand: Daikin Pages: 178

Brand: Vax Pages: 16

Brand: Kelvinator Pages: 16

Brand: Trotec Pages: 16

Brand: Technibel Pages: 34

Brand: Daikin Pages: 10

Duplex Water-Cooled Hermetic CenTraVac

Brand: Trane Pages: 80

Brand: U.S. Products Pages: 12

Brand: Daikin Pages: 68

Brand: Daikin Pages: 32

Brand: innovair Pages: 12

Brand: innovair Pages: 58

Brand: Johnson Controls Pages: 4

GERMAGIC PAC-5801

Brand: Giabo Pages: 24

york YSHC18FSAADG

Brand: Johnson Controls Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands